Ist der nand speicher bei meiner gp2x kaputt?


moogman

Still Fresh
Joined
Feb 22, 2007
Messages
97
so, hab heute mal das serielle kabel angeschlossen und den bootvorgang angeschaut ich kenn mich damit nicht so aus aber, das ding sagt das was mit dem crc nicht passt, ist da was kaputt oder ist das okay so,
ich hab auch das jtag interface sollte ich vielleicht nochmal die firmware flashen?
--------------------------log-----------------------------------------
U-Boot 1.0.0 (Dec 7 2006 - 16:07:11)

U-Boot code: 03E00000 -> 03E49610 BSS: -> 03E82208
IRQ Stack: 03ea3204
FIQ Stack: 03ea4204
DRAM Configuration:
Bank #0: 00100000 63 MB
Flash: 0 kB
NAND:probing at 0x9c000000
Flash chip found:
Manufacturer ID: 0xEC, Chip ID: 0x76 (Samsung K9F1208 64Mb)
1 flash chips found. Total nand_chip size: 64 MB
Get Environment from NAND offset 0x70000 ...
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial

NAND read: device 0 offset 0x1a0000, size 0x40000 ... 262144 bytes read: OK

NAND read: device 0 offset 0x80000, size 0xb0000 ... 720896 bytes read: OK
### main_loop: bootcmd="bootm"
Hit any key to stop autoboot: 0
## Booting image at 01000000 ...
Image Name: MMSP2 Linux Kernel
Created: 2006-12-18 4:51:31 UTC
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 651272 Bytes = 636 kB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

MMC/SD Card Detected
MMC/SD Slot initialized
Partition check:
mmcsda: p1
Register SD: 968MsB
mount...1
mount...2:
Reading data from NAND FLASH without ECC is not recommended
Freeing init memory: 280K
INIT: version 2.84 booting
<7>**>>ecc error unfixed on chunk 3268:0
umount: /mnt/sd: Invalid argument
<7>**>>ecc error unfixed on chunk 1891:0
Started device management daemon v1.3.25 for /dev
MSDOS FS: IO charset utf8
Apply LCD Timing
Using /lib/modules/2.4.25/kernel/drivers/usb/gadget/net2272.o
net2272: Set 2272 bus timing
USB SUSPEND MODE
net2272: PLX NET2272 USB Peripheral Controller
net2272: irq 222, mapped mem c280c000, chip rev 0011
net2272: running in 16-bit, byte normal bus mode
net2272: version: 2006 April 5, v3
net2272: unbind
Using /lib/modules/2.4.25/kernel/drivers/usb/usbcore.o
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
Using /lib/modules/2.4.25/kernel/arch/arm/mach-mmsp2/mmsp2_usbh.o
mmsp2_usbh.c: USB
mmsp2_usbh.c: initializing MMSP2 USB host PCI-DMA workaround
Using /lib/modules/2.4.25/kernel/drivers/usb/host/usb-ohci.o
Using /lib/modules/2.4.25/kernel/drivers/usb/host/usb-ohci-mmsp2.o
f_fact = 4, f_clk = 49766400, f_err = +1766400
a_fact = 3, a_clk = 49152000, a_err = +1152000
u_fact = 1, u_clk = 95846400, u_err = +47846400
usb-ohci.c: USB OHCI at membase 0xf0004300, IRQ 13
usb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: f0004300
hub.c: USB hub found
hub.c: 2 ports detected
kusbd_policy: /sbin/hotplug add 1, ret=0x0
loading usb host drivers...
Using /lib/modules/2.4.25/kernel/drivers/scsi/scsi_mod.o
SCSI subsystem driver Revision: 1.00
Using /lib/modules/2.4.25/kernel/drivers/scsi/sd_mod.o
hub.c: new USB device <NULL>-1, assigned address 2
Product: USB2.0 Hub
hub.c: USB hub found
hub.c: 4 ports detected
kusbd_policy: /sbin/hotplug add 2, ret=0x0
Using /lib/modules/2.4.25/kernel/drivers/usb/storage/usb-storage.o
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Using /lib/modules/2.4.25/kernel/drivers/input/input.o
hub.c: new USB device <NULL>-2, assigned address 3
usb.c: USB device not accepting new address=3 (error=-110)
Using /lib/modules/2.4.25/kernel/drivers/usb/hid.o
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech>
hid-core.c: USB HID support drivers
hub.c: new USB device <NULL>-2, assigned address 4
usb.c: USB device not accepting new address=4 (error=-110)
Using /lib/modules/2.4.25/kernel/drivers/input/keybdev.o
Using /lib/modules/2.4.25/kernel/drivers/input/mousedev.o
mice: PS/2 mouse device common for all mice
hub.c: new USB device <NULL>-1.4, assigned address 5
Manufacturer: Genesyslogic
Using /lib/modules/2.4.2P5/kernel/driversr/input/eodvdev.o
uct: USB Mass Storage Device
scsi0 : SCSI emulation for USB Mass Storage devices
 
Nein, das ist normal.
Es gibt keinen NAND OHNE Error. Ein paar Blocks sind immer kaputt, und der gp2x loggt alles mit.
Und die BAD CRC beim Environment ist da, weil der gp2x kein Environment setzt ;)
 
EvilDragon said:
Nein, das ist normal.
Es gibt keinen NAND OHNE Error. Ein paar Blocks sind immer kaputt, und der gp2x loggt alles mit.
Und die BAD CRC beim Environment ist da, weil der gp2x kein Environment setzt ;)
gegenfrage wieviele sind normal

meine ganze dmesg ausgabe besteht nur da draus....
 
@boeseronkel2k

Ist bei mir genau so...
Warum verkaufen die eigentlich defekte Bauteile? :)
 
Back
Top